TurboJohn LLC © 2024
Designed by TurboJohn LLC © 2024

RaceQuip’s Jr. Dragster / Quarter Midget 5-Point Latch & Link Harness System features twin individual shoulder belts and has an SFI 16.2 Rating. This motorsports seat belt system also has a `pull-up` lap belt design which means you pull the lap belt ends toward the cam buckle to tighten the belts. This auto racing harness is manufactured with 2" premium polyester webbing and double-adjustable ends to help ease installation. Mounting is either wrap around or bolt-in and the harness set comes with drop-forged steel 3-bar slides and bolt on ends (bolts not included). Shoulders adjust from 15" to 40" and lap belt adjusts from 22" to 60". Not for adult use in a full size racecar. NOTE: RaceQuip motorsports harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a race vehicle to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, red, blue, purple and pink - one "set" of seat belts equals one seat.

RaceQuip’s Latch & Link 5-point auto racing harness set has twin individual shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". All RaceQuip 711 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, red, blue, yellow, purple, platinum, green, pink, and orange - one "set" of seat belts equals one seat.

RaceQuip’s Latch & Link 6-point auto racing harness set has twin individual shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". All RaceQuip 712 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the dual sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black or red - one "set" of seat belts equals one seat.

RaceQuip�s Latch & Link V-Style auto racing harness set has shoulder belts that attach to a single mount point behind the seat, thus forming a "V" shape. Sometimes also referred to as 4-Point belts, these sets are manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 26" to 40" and the lap belt adjusts from 20" to 60". All RaceQuip 713 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends - except shoulders, they have a bolt on end sewn in place. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, red, and blue - one "set" of seat belts equals one seat.

RaceQuip�s Latch & Link 5-point HANS / HNR auto racing harness set has twin individual shoulder belts that are reduced to 2" above the adjusters to more easily accomodate a HANS or Head and Neck Restraint Device. These belts are manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". All RaceQuip 717 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, red, and blue - one "set" of seat belts equals one seat.

RaceQuip’s Latch & Link 6-point HANS / HNR auto racing harness set has twin individual shoulder belts that are reduced to 2" above the adjusters to more easily accomodate a HANS or Head and Neck Restraint Device. These belts are manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". All RaceQuip 718 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the dual sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black or red - one "set" of seat belts equals one seat.

RaceQuip's all 2" small buckle Latch & Link Pro 5-point auto racing harness set has twin individual HANS / HNR style shoulder belts and is manufactured using premium polyester webbing and drop forged steel black hardware to exceed the SFI 16.1 rating. Shoulders are 2" width to accommodate a HANS or other Head & Neck Restraint Device and adjust from 26" to 62" in length. The 2" wide lap belt adjusts from 30" to 65". Many racers now prefer a 2" lap belt because it tucks under the iliac crest (hip bone) so that you can get the lap belt tighter. This harness set is a "pull up lap" design, which means that the lap belt straps must be pulled up and toward the center latch & link buckle mechanism to tighten the belts . This 2" Pro Harness set features a small compact design buckle that is lightweight and stays out of the way. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the lever is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). The buckle and all the hardware is black oxide coated for good looks and durability. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, one "set" of seat belts equals one seat.

RaceQuip's small buckle Latch & Link Pro 6-point auto racing harness set has twin individual style shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel black hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". This harness set is a "pull down lap" design, which means that the lap belt straps must be pulled down and away from the center latch & link buckle mechanism to tighten the belts . This Pro Harness set features a small compact design buckle that is lightweight and stays out of the way. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the lever is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). The buckle and all the hardware is black oxide coated for good looks and durability. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black or red, one "set" of seat belts equals one seat.

RaceQuip's small buckle Latch & Link Pro 5 point ratchet auto racing harness set has twin individual style shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel black hardware to exceed the SFI 16.1 rating. Shoulders adjust from 28" to 60" and the lap belt adjusts from 40" to 78". This set utiizes a ratchet on the left side lap belt to adjust the tension and get the harness sinched down tight. The ratcheting mechanism is cranked by hand with the included 1/4" ratchet handle. This Pro Ratcheting Harness set features a small compact design buckle that is lightweight and stays out of the way. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the lever is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). The buckle and all the hardware is black oxide coated for good looks and durability. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, one "set" of seat belts equals one seat.

RaceQuip's small buckle Latch & Link Pro 5 point ratchet auto racing harness set has twin individual style shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel black hardware to exceed the SFI 16.1 rating. Shoulders are 3" to 2" HANS / HNR style and adjust from 28" to 60" and the lap belt adjusts from 40" to 78". This set utiizes a ratchet on the left side lap belt to adjust the tension and get the harness sinched down tight. The ratcheting mechanism is cranked by hand with the included 1/4" ratchet handle. This HNR Pro Ratcheting Harness set features a small compact design buckle that is lightweight and stays out of the way. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the lever is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). The buckle and all the hardware is black oxide coated for good looks and durability. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, one "set" of seat belts equals one seat.

RaceQuip's Latch & Link 5-point HANS / HNR auto racing harness set has twin individual shoulder belts that are reduced to 2" above the adjusters to more easily accomodate a HANS or Head and Neck Restraint Device. These belts are manufactured using premium 3" polyester webbing and drop forged steel hardware to exceed the SFI 16.1 rating. Shoulders adjust from 20" to 62" and the lap belt adjusts from 20" to 60". All RaceQuip 817 series belts come as a "pull down lap" design, which means that the lap belts must be pulled down and away from the center latch & link buckle mechanism to tighten. The buckle and all the hardware is black oxide coated for good looks and durability. All RaceQuip Latch & Link motorsports harness sets are distinguished by a pivoting "hammer," called a Duckbill, which is located on the lap belt and locks all of the belts into place by snapping down into a detent. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the Duckbill is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black, one "set" of seat belts equals one seat.

RaceQuip's small buckle Latch & Link Pro 6-point auto racing harness set has twin individual HANS / HNR style shoulder belts and is manufactured using premium 3" polyester webbing and drop forged steel black hardware to exceed the SFI 16.1 rating. Shoulders are 3" to 2" design to accommodate a HANS or other Head & Neck Restraint Device and adjust from 20" to 62" in length. The lap belt adjusts from 20" to 60". This harness set is a "pull down lap" design, which means that the lap belt straps must be pulled down and away from the center latch & link buckle mechanism to tighten the belts . This Pro Harness set features a small compact design buckle that is lightweight and stays out of the way. Both shoulder belts and the sub-belt are hooked over the link; the link is inserted into the latch on the lap belt; the lever is then brought down into and over the link, securely holding all of the pieces in place. Since RaceQuip seat belt sets are "double adjustable", lengths are simply adjusted on either end for ease of installation. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place with the supplied ends (bolts not included). The buckle and all the hardware is black oxide coated for good looks and durability. Snap hook ends and eyebolts are sold separately if the user wishes to install belts in that manner. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use. They are only to be used in racing vehicles off of public streets and highways. All racing harness sets are designed to be mounted in a racecar to a rollcage or harness bar - if you do not have either, you should not try to install any RaceQuip harness set or seat belts. Available in black or red, one "set" of seat belts equals one seat.